Pump Monitoring Solution

Data-Command offers a cloud-based storage tank and pump monitoring solution to deliver critical station and alarm information in real-time.  Remote monitoring of your pumps can significantly improve your ability to defer major costs due to equipment failure or process upsets.

Pumps with Electric Check Valves

Our products pull information from either our installed, or your pre-existing hardware, and sends it to one of our data centers. Users are then notified in the event of a problem. Additionally, users are able to monitor and control their pumps through our secure Data-Command Info-Portal™ via any internet connected device, such as a PC, tablet, or smartphone.

Mobile Lift Station Monitoring

At any time, users can easily view a set of informative displays, alerts, reports, and trends. These displays are customized to show vital pump station monitoring points in a way that is simple to navigate. 

Info-Portal - Graphic

Mobile Access allows fewer people to do more. Reduced management requirements enable small teams to handle expanding projects, while still allowing key pump station monitoring metrics:

  • Status (currently running or stopped)
  • Number of pump cycles
  • pump Runtime hours
  • Pump failure
  • Pump flows, Flow Totalization
  • Storage Tank Levels
  • Storage Tank Alarms

Save money. Smaller teams, reduced travel time and costs, save municipalities considerable budget space on new projects and upgrades.

    • Eliminate avoidable EPA violations due to low suction pressure, low tank levels or low chemical levels
    • Helps notify maintenance crews broken mains more quickly
    •  Avoid Storage Tank overflow issues
    • Get rid of expensive leased line
    • Eliminate unnecessary trips

  • Greatly reduced administration time

About Storage Tanks and Pump monitoring

Pump monitoring is a major part of any manufacturing industry.

In a municipal Water Treatment systems

In a municipality, there is a network of water pipes that routes treated water from a water treatment plant to the residents of the community. In most cases the water is in some form of storage tank, either an elevated tank or standpipe to be used within the day and to make sure the community has fire protection. When these storage tanks are located farther from the plant and the water travels up and down hill, it loses pressure. If the pressure falls below certain critical levels, it creates a health risk, as well as a risk of running out of water. One way to maintain the required pressure is to use a “booster” station.  A pump station is composed of a set of pumps that increase the pressure in the line and can be used to fill a downstream storage tank. Because of hydraulics, the storage tank is what is actually maintaining the pressure and the pump station is just used to fill the tank.

In a municipal Waste Water Treatment systems

Sewage pump stations also known as lift stations, are a major part of a municipal wastewater collection system. In a municipality, there is a network of sewers that convey the sanitary sewer water, and sometimes storm water to a wastewater treatment plant. These sewers operate by utilizing gravity to make the waste water flow downhill. In low areas where water stops before reaching the treatment plant, it must be “lifted” to a higher elevation for the gravity process to continue.

To lift this water to the higher elevation, it is necessary to use pumps. Prior to pumping, water is collected in what is referred to in the industry as a wet well. This is nothing more than a large holding tank usually in the form of an underground concrete vault. Pumps turn on and off based on when this wet well reaches certain levels. At high levels pumps turn on, and at low levels pumps turn off.

In the Oil and Gas Industry

When extracting oil from deep within the ground the iconic pump jack comes to mind.  Seen in lots of old movies and shows, this pump is made up of several different components that pumps petroleum from deep within the ground up to a holding tank or into a distribution of pipes which eventually end up at a refinery.   Keeping these pumps operating at peak efficiency is essential to making money and producing oil.  As seen from a Google map over Texas, these structures pepper the landscape for miles.  Maintaining each one without remote monitoring can be very inefficient and costly.  These pump jacks use energy to operate but not all of them run all the time, only the most efficient ones should be operating. Keeping track of which ones are pumping most efficiently is the daily challenge. 

Receive and Acknowledge Alerts via Text, Voice Call, or Email:

Product Features Also Include:

    • Use any internet connection (i.e. Cellular, DSL, Cable, Satellite)

    • Customized Displays

    • Customized Reports

    • Customized Trends

    • Unlimited Users access

    • Free Tech Support

  • Free updates

Mobile Dashboards

Our Data-Command Info-Portal™ dashboards enable our users to view and manage their equipment and processes. Dashboards can be customized to provide high quality visualization of how equipment is performing. This also allows operations and maintenance personnel to monitor operations 24/7.

Transmitting from these sites to our servers using cellular or Ethernet technology enables users to easily check locations using a PC or mobile device, such as a smartphone or tablet.

Operations and maintenance personnel can easily view system data at any time by logging into the Data-Command Info-Portal™. Customized displays, alerts, reports, and trends present information in a clear and concise format.

Our Hardware & Software Solutions

The depth of our hardware and software products is what differentiates us from our competitors. By enabling our clients to connect just about any piece of equipment to our cloud-based servers, we are able to give them increased access to a wider range of information.  This ultimately gives our users remote access and control of their system. We can utilize cost effective connections such as cellular, satellite, DSL, and cable to reach practically any equipment, anywhere you may have it.


Hardwire Solution


Talk to your SCADA or PLC


Redundant or contingency

SCADA in the Cloud

Redundant or contingency





Data Command Logo with Data Bridge





Learn More >


Learn More >


Learn More >


Learn More >